1、要檢查分電器、火花塞、高壓線等是否因為汽車淋雨等受潮，如果是這樣，可以把受潮機件晾干，然后再發動。

1. To check if the power distributor, spark plug, high-voltage wire, etc. are damp due to car rain or other factors, you can air dry the damp parts before starting.

2、檢查火花塞是否損壞，如果損壞，只要更換新火花塞即可。

2. Check if the spark plug is damaged. If it is, simply replace it with a new spark plug.

3、檢查蓄電池電壓是否足夠。有的時候，停車忘記關燈，時間長了，就可能耗盡電源。如果是這樣，把車掛二擋，腳踩離合，用車拖拽(一般不建議，做好找人推一下)，當行駛到一定速度時，松開離合，擰動點火開關(一般不建議，應當在推到之前將點火開關開到ON檔上)，汽車就能夠啟動。如果是發電機有問題，此法不能奏效。

3. Check if the battery voltage is sufficient. Sometimes, if you forget to turn off the lights while parking, over time, you may run out of power. If that's the case, put the car in second gear, step on the clutch, drag the car (generally not recommended, do a good job of finding someone to push it), when driving to a certain speed, release the clutch, turn the ignition switch (generally not recommended, should turn the ignition switch to ON before pushing it), and the car can start. If there is a problem with the generator, this method will not work.

換擋時發動機熄火行進中換擋，如果操作規范，但出現熄火現象，需要檢查以下問題：

When shifting gears, if the engine is turned off while moving, and the operation is standardized but the engine is turned off, the following issues need to be checked:

1、看怠速是否穩定，怠速是否過低，如果怠速不穩或怠速低，只要把怠速調整到正常轉速即可。還要把怠速截止閥擰緊，插頭插緊。

1. Check if the idle speed is stable and low. If the idle speed is unstable or low, simply adjust the idle speed to normal speed. Also tighten the idle stop valve and plug it in tightly.

2、如果怠速正常，則可能是化油器被堵塞，需要到專業修理站清洗化油器。

2. If the idle speed is normal, it may be that the carburetor is blocked and needs to be cleaned at a professional repair station.

高速行駛時方向盤震顫，汽車在高速行駛或在某一較高車速行駛時出現行駛不穩、擺頭，甚至方向盤抖動，出現這種情況的原因有如下幾點：

When driving at high speeds, the steering wheel shakes, causing the car to experience unstable driving, shaking of the head, or even shaking of the steering wheel. The reasons for this situation are as follows:

1、前輪定位角失準，前束過大。

1. Misalignment of front wheel alignment angle and excessive toe in.

2、前輪胎氣壓過低或輪胎由于修補等原因起動不平衡。

2. The front tire pressure is too low or the tire starts unevenly due to repair or other reasons.

3、前輪輻變形或輪胎螺栓數量不等。

3. Distorted front wheel spokes or varying number of tire bolts.

4、傳動系統零部件安裝松動。

4. Loose installation of transmission system components.

5、傳動軸彎曲，動力不平衡，前軸變形。

5. Bending of the transmission shaft, power imbalance, and deformation of the front axle.

6、減振器故障。

6. Shock absorber malfunction.

本文由濟南奔馳汽車維修友情奉獻.更多有關的知識請點擊:http://m.nanofluidizer.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by Jinan Mercedes Benz Automotive Maintenance Friendship. For more related knowledge, please click: http://m.nanofluidizer.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned